D-Link Dir-632A переназначить WAN

Post new topic   Reply to topic    DD-WRT Forum Index -> Оборудование на основе Atheros WiSOC
Author Message
vudstik
DD-WRT Novice


Joined: 25 Sep 2014
Posts: 5

PostPosted: Thu Sep 25, 2014 14:41    Post subject: D-Link Dir-632A переназначить WAN Reply with quote
Здравствуйте.
D-Link DIR-632A
Atheros AR9341 rev 1.1 (0x0121)
DD-WRT v24-sp2 (06/23/14) - build 24461


После грозы перестал появляться интернет, хотя индикатор горит постоянно, что с кабелем провайдера, что без него.
Пробовал через swconfig dev … show но в ответ получал Failed to connect to the switch

Есть ли возможность на данной модели переназначить WAN-порт? Если да, как именно это сделать?
Заранее благодарен!
Sponsor
vasek00
DD-WRT Guru


Joined: 06 Nov 2010
Posts: 3312

PostPosted: Fri Sep 26, 2014 5:52    Post subject: Re: D-Link Dir-632A переназначить WAN Reply with quote
vudstik wrote:
Здравствуйте.
D-Link DIR-632A
Atheros AR9341 rev 1.1 (0x0121)
DD-WRT v24-sp2 (06/23/14) - build 24461


После грозы перестал появляться интернет, хотя индикатор горит постоянно, что с кабелем провайдера, что без него.
Пробовал через swconfig dev … show но в ответ получал Failed to connect to the switch

Есть ли возможность на данной модели переназначить WAN-порт? Если да, как именно это сделать?
Заранее благодарен!


По информации http://www.dd-wrt.com/phpBB2/viewtopic.php?p=477147 или http://www.dd-wrt.com/wiki/index.php/Supported_Devices и других источников в данном роутере стоит:
CPU-AR7241 или AR7242, switch-RTL8309G, radio-AR9287
Как раз и интересно полный формат команды swconfig dev ...?
И какое имя присвоено switch если посмотреть dmesg, где-то между строчек (которые ...):
Code:
<6>[    0.840000] 8021q: 802.1Q VLAN Support v1.8
<6>[    0.850000] searching for nvram
<6>[    0.850000] nvram size = 0
<6>[    0.920000] Atheros AR71xx hardware watchdog driver version 0.1.0
<6>[    0.930000] ar71xx-wdt: timeout=15 secs (max=21) ref freq=200000000
<6>[    0.940000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
<6>[    0.950000] Freeing unused kernel memory: 188K (80371000 - 803a0000)
<7>[    4.090000] ar71xx-wdt: enabling watchdog timer
....
<6>[    4.280000] libphy: ag71xx_mdio: probed
<6>[    4.850000] ar8316: Using port 4 as switch port
<6>[    5.340000] ag71xx ag71xx.0 (unregistered net_device): connected to PHY at ag71xx-mdio.0:00 [uid=004dd041, driver=Atheros AR8216/AR8236/AR8316]
<6>[    5.350000] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:RGMII
vudstik
DD-WRT Novice


Joined: 25 Sep 2014
Posts: 5

PostPosted: Mon Sep 29, 2014 5:24    Post subject: Reply with quote
Вывод dmesg dev следующий, но информацию про switch обнаружить не удалось.


<6>[ 0.410000] pci 0000:00:00.0: fixup device configuration
<0>[ 0.410000] bootstrap returns device 168C:2E
<7>[ 0.420000] pci 0000:00:00.0: reg 10: [mem 0x00000000-0x0000ffff 64bit]
<7>[ 0.420000] pci 0000:00:00.0: supports D1
<7>[ 0.420000] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
<6>[ 0.420000] pci 0000:00:00.0: BAR 0: assigned [mem 0x10000000-0x1000ffff 64bit]
<6>[ 0.420000] PCI: mapping irq 72 to pin1@0000:00:00.0
<6>[ 0.430000] Switching to clocksource MIPS
<6>[ 0.430000] NET: Registered protocol family 2
<6>[ 0.440000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
<6>[ 0.440000] TCP established hash table entries: 1024 (order: 1, 8192 bytes)
<6>[ 0.450000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
<6>[ 0.450000] TCP: Hash tables configured (established 1024 bind 1024)
<6>[ 0.460000] TCP: reno registered
<6>[ 0.460000] UDP hash table entries: 256 (order: 0, 4096 bytes)
<6>[ 0.470000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
<6>[ 0.480000] NET: Registered protocol family 1
<7>[ 0.480000] PCI: CLS 0 bytes, default 32
<5>[ 0.480000] gpio_proc: module loaded and /proc/gpio/ created
<5>[ 0.490000] wl0gpio_proc: module loaded and /proc/wl0gpio/ created
<6>[ 0.500000] squashfs: version 3.0 (2006/03/15) Phillip Lougher
<6>[ 0.500000] msgmni has been set to 56
<6>[ 0.510000] io scheduler noop registered
<6>[ 0.510000] io scheduler deadline registered (default)
<6>[ 0.510000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
<6>[ 0.540000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A
<6>[ 0.550000] console [ttyS0] enabled, bootconsole disabled
<0>[ 0.560000] guessed flashsize = 8M
<0>[ 0.570000] scanning for root partition
<0>[ 0.570000] uboot detected
<0>[ 0.570000] guessed bootloader size = 50000
<0>[ 0.580000]
<0>[ 0.580000] found squashfs at 143000
<5>[ 0.590000] Creating 8 MTD partitions on "ar7240-nor0":
<5>[ 0.590000] 0x000000000000-0x000000050000 : "RedBoot"
<5>[ 0.600000] 0x000000050000-0x0000007e0000 : "linux"
<5>[ 0.600000] 0x000000143000-0x0000006f0000 : "rootfs"
<4>[ 0.610000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
<5>[ 0.620000] mtd: partition "rootfs" set to be root filesystem
<5>[ 0.630000] 0x0000006f0000-0x0000007e0000 : "ddwrt"
<5>[ 0.640000] 0x0000007e0000-0x0000007f0000 : "nvram"
<5>[ 0.640000] 0x0000007f0000-0x000000800000 : "board_config"
<5>[ 0.650000] 0x000000000000-0x000000800000 : "fullflash"
<5>[ 0.660000] 0x000000000000-0x000000050000 : "fullboot"
<6>[ 0.660000] tun: Universal TUN/TAP device driver, 1.6
<6>[ 0.670000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
<4>[ 0.670000] AG7240: Length per segment 1544
<4>[ 0.680000] AG7240: Max segments per packet 1
<4>[ 0.680000] AG7240: Max tx descriptor count 64
<4>[ 0.690000] AG7240: Max rx descriptor count 128
<4>[ 0.690000] AG7240: fifo cfg 3 01f00140
<4>[ 0.700000] AG7240CHH: Mac address for unit 0
<4>[ 0.700000] AG7240CHH: 00:18:e7:e0:0d:61
<4>[ 0.910000] AG7240CHH: Mac address for unit 1
<4>[ 0.910000] AG7240CHH: ff:ff:ff:ff:ff:ff
<6>[ 1.110000] PPP generic driver version 2.4.2
<6>[ 1.120000] PPP BSD Compression module registered
<6>[ 1.120000] PPP Deflate Compression module registered
<6>[ 1.130000] PPP MPPE Compression module registered
<6>[ 1.140000] NET: Registered protocol family 24
<7>[ 1.140000] Registered led device: generic_0
<7>[ 1.140000] Registered led device: generic_1
<7>[ 1.140000] Registered led device: generic_2
<7>[ 1.140000] Registered led device: generic_3
<7>[ 1.140000] Registered led device: generic_4
<7>[ 1.140000] Registered led device: generic_5
<7>[ 1.140000] Registered led device: generic_6
<7>[ 1.140000] Registered led device: generic_7
<7>[ 1.140000] Registered led device: generic_8
<7>[ 1.140000] Registered led device: generic_9
<7>[ 1.140000] Registered led device: generic_10
<7>[ 1.140000] Registered led device: generic_11
<7>[ 1.140000] Registered led device: generic_12
<7>[ 1.140000] Registered led device: generic_13
<7>[ 1.140000] Registered led device: generic_14
<7>[ 1.150000] Registered led device: generic_15
<7>[ 1.150000] Registered led device: generic_16
<7>[ 1.150000] Registered led device: generic_17
<7>[ 1.150000] Registered led device: generic_18
<7>[ 1.150000] Registered led device: generic_19
<7>[ 1.150000] Registered led device: generic_20
<7>[ 1.150000] Registered led device: generic_21
<7>[ 1.150000] Registered led device: generic_22
<7>[ 1.150000] Registered led device: generic_23
<7>[ 1.150000] Registered led device: generic_24
<7>[ 1.150000] Registered led device: generic_25
<7>[ 1.150000] Registered led device: generic_26
<7>[ 1.150000] Registered led device: generic_27
<7>[ 1.150000] Registered led device: generic_28
<7>[ 1.150000] Registered led device: generic_29
<7>[ 1.150000] Registered led device: generic_30
<7>[ 1.150000] Registered led device: generic_31
<7>[ 1.150000] Registered led device: wireless_generic_0
<7>[ 1.150000] Registered led device: wireless_generic_1
<7>[ 1.150000] Registered led device: wireless_generic_2
<7>[ 1.150000] Registered led device: wireless_generic_3
<7>[ 1.150000] Registered led device: wireless_generic_4
<7>[ 1.150000] Registered led device: wireless_generic_5
<7>[ 1.150000] Registered led device: wireless_generic_6
<7>[ 1.150000] Registered led device: wireless_generic_7
<7>[ 1.150000] Registered led device: wireless_generic_8
<7>[ 1.150000] Registered led device: wireless_generic_9
<7>[ 1.150000] Registered led device: wireless_generic_10
<7>[ 1.150000] Registered led device: wireless_generic_11
<7>[ 1.150000] Registered led device: wireless_generic_12
<7>[ 1.150000] Registered led device: wireless_generic_13
<7>[ 1.150000] Registered led device: wireless_generic_14
<7>[ 1.160000] Registered led device: wireless_generic_15
<6>[ 1.160000] u32 classifier
<6>[ 1.160000] Performance counters on
<6>[ 1.160000] input device check on
<6>[ 1.170000] Actions configured
<6>[ 1.170000] Netfilter messages via NETLINK v0.30.
<6>[ 1.170000] nf_conntrack version 0.5.0 (452 buckets, 1808 max)
<4>[ 1.180000] nf_conntrack_rtsp v0.6.21 loading
<4>[ 1.190000] nf_nat_rtsp v0.6.21 loading
<6>[ 1.190000] ip_tables: (C) 2000-2006 Netfilter Core Team
<6>[ 1.200000] IPP2P v0.8.2 loading
<6>[ 1.200000] TCP: westwood registered
<6>[ 1.200000] TCP: hybla registered
<6>[ 1.210000] TCP: vegas registered
<6>[ 1.210000] NET: Registered protocol family 17
<5>[ 1.210000] Bridge firewalling registered
<6>[ 1.220000] 8021q: 802.1Q VLAN Support v1.8
<6>[ 1.220000] searching for nvram
<6>[ 1.230000] nvram size = 0
<6>[ 1.260000] Atheros AR71xx hardware watchdog driver version 0.1.0
<6>[ 1.260000] ar71xx-wdt: timeout=15 secs (max=21) ref freq=200000000
<6>[ 1.280000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
<6>[ 1.280000] Freeing unused kernel memory: 160k freed
<7>[ 4.020000] ar71xx-wdt: enabling watchdog timer
<4>[ 4.130000] ag7240_ring_alloc Allocated 1024 at 0x81ecb800
<4>[ 4.140000] ag7240_ring_alloc Allocated 2048 at 0x81cd8000
<6>[ 4.140000] reg init for 0
<4>[ 4.150000] Setting PHY...
<6>[ 6.140000] rtl phy0 id 0:0
<6>[ 6.150000] rtl phy1 id 0:0
<6>[ 6.150000] rtl phy2 id 0:0
<6>[ 6.150000] rtl phy3 id 0:0
<6>[ 6.150000] rtl phy4 id 0:0
<6>[ 6.160000] rtl phy5 id 0:0
<6>[ 6.160000] rtl phy6 id 0:0
<6>[ 6.160000] rtl phy7 id 0:0
<4>[ 6.170000] AG7240: enet unit:0 is up...
<4>[ 6.170000] Mii 100Mbps full duplex
<4>[ 6.170000] AG7240: done cfg2 0x7115 ifctl 0x0 miictrl
<4>[ 6.180000] ag7240_ring_alloc Allocated 1024 at 0x81fd5c00
<4>[ 6.190000] ag7240_ring_alloc Allocated 2048 at 0x81fc4800
<6>[ 6.200000] reg init for 1
<4>[ 6.200000] ATHRS26: resetting s26
<4>[ 6.300000] ATHRS26: s26 reset done
<4>[ 6.310000] Setting PHY...
<6>[ 7.520000] Loading modules backported from Linux version master-2014-05-22-0-gf2032ea
<6>[ 7.530000] Backport generated by backports.git backports-20140320-37-g5c33da0
<6>[ 7.700000] cfg80211: Calling CRDA to update world regulatory domain
<6>[ 7.740000] cfg80211: World regulatory domain updated:
<6>[ 7.740000] cfg80211: DFS Master region: unset
<6>[ 7.740000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
<6>[ 7.750000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
<6>[ 7.760000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
<6>[ 7.770000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
<6>[ 7.780000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
<6>[ 7.790000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
<6>[ 7.790000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
<4>[ 8.180000] AG7240: unit 0: phy 0 not up carrier 1
<7>[ 8.380000] ath: EEPROM regdomain: 0x30
<7>[ 8.380000] ath: EEPROM indicates we should expect a direct regpair map
<7>[ 8.380000] ath: Country alpha2 being used: AM
<7>[ 8.380000] ath: Regpair used: 0x30
<7>[ 8.400000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
<7>[ 8.400000] Registered led device: ath9k-phy0
<6>[ 8.400000] ieee80211 phy0: Atheros AR9287 Rev:2 mem=0xb0000000, irq=72
<6>[ 8.410000] cfg80211: Calling CRDA for country: AM
<6>[ 8.430000] cfg80211: Regulatory domain changed to country: AM
<6>[ 8.430000] cfg80211: DFS Master region: ETSI
<6>[ 8.440000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
<6>[ 8.450000] cfg80211: (2402000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
<6>[ 8.450000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 1800 mBm), (N/A)
<6>[ 8.460000] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz), (N/A, 1800 mBm), (N/A)
<4>[ 10.180000] AG7240: enet unit:0 is up...
<4>[ 10.180000] Mii 100Mbps full duplex
<4>[ 10.180000] AG7240: done cfg2 0x7115 ifctl 0x0 miictrl
<6>[ 11.080000] device br0 entered promiscuous mode
<4>[ 11.130000] ag7240_ring_free Freeing at 0x81ecb800
<4>[ 11.130000] ag7240_ring_free Freeing at 0x81cd8000
<4>[ 11.150000] ag7240_ring_alloc Allocated 1024 at 0x81ecb800
<4>[ 11.160000] ag7240_ring_alloc Allocated 2048 at 0x81cd8000
<6>[ 11.170000] reg init for 0
<4>[ 11.170000] Setting PHY...
<6>[ 13.160000] rtl phy0 id 0:0
<6>[ 13.170000] rtl phy1 id 0:0
<6>[ 13.170000] rtl phy2 id 0:0
<6>[ 13.170000] rtl phy3 id 0:0
<6>[ 13.170000] rtl phy4 id 0:0
<6>[ 13.180000] rtl phy5 id 0:0
<6>[ 13.180000] rtl phy6 id 0:0
<6>[ 13.180000] rtl phy7 id 0:0
<4>[ 13.190000] AG7240: enet unit:0 is up...
<4>[ 13.190000] Mii 100Mbps full duplex
<4>[ 13.190000] AG7240: done cfg2 0x7115 ifctl 0x0 miictrl
<4>[ 13.210000] ag7240_ring_free Freeing at 0x81ecb800
<4>[ 13.210000] ag7240_ring_free Freeing at 0x81cd8000
<4>[ 13.230000] ag7240_ring_alloc Allocated 1024 at 0x81ecb800
<4>[ 13.240000] ag7240_ring_alloc Allocated 2048 at 0x81cd8000
<6>[ 13.250000] reg init for 0
<4>[ 13.250000] Setting PHY...
<6>[ 15.240000] rtl phy0 id 0:0
<6>[ 15.250000] rtl phy1 id 0:0
<6>[ 15.250000] rtl phy2 id 0:0
<6>[ 15.250000] rtl phy3 id 0:0
<6>[ 15.260000] rtl phy4 id 0:0
<6>[ 15.260000] rtl phy5 id 0:0
<6>[ 15.260000] rtl phy6 id 0:0
<6>[ 15.260000] rtl phy7 id 0:0
<4>[ 15.270000] AG7240: enet unit:0 is up...
<4>[ 15.270000] Mii 100Mbps full duplex
<4>[ 15.270000] AG7240: done cfg2 0x7115 ifctl 0x0 miictrl
<6>[ 15.290000] device eth0 entered promiscuous mode
<6>[ 15.300000] br0: port 1(eth0) entered forwarding state
<6>[ 15.310000] br0: port 1(eth0) entered forwarding state
<6>[ 15.310000] device br0 left promiscuous mode
<6>[ 15.320000] device br0 entered promiscuous mode
<6>[ 15.400000] cfg80211: Calling CRDA to update world regulatory domain
<3>[ 15.410000] cfg80211: Invalid regulatory domain detected:
<6>[ 15.410000] cfg80211: Regulatory domain: 00
<6>[ 15.420000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
<6>[ 15.430000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
<6>[ 15.430000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
<6>[ 15.440000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
<6>[ 15.450000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
<6>[ 15.460000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
<6>[ 15.470000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
<6>[ 15.500000] cfg80211: Calling CRDA to update world regulatory domain
<6>[ 15.510000] cfg80211: World regulatory domain updated:
<6>[ 15.520000] cfg80211: DFS Master region: unset
<6>[ 15.520000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
<6>[ 15.530000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
<6>[ 15.540000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
<6>[ 15.550000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
<6>[ 15.550000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
<6>[ 15.560000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
<6>[ 15.570000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
<6>[ 15.690000] cfg80211: Calling CRDA for country: US
<6>[ 15.690000] cfg80211: Regulatory domain changed to country: US
<6>[ 15.700000] cfg80211: DFS Master region: FCC
<6>[ 15.700000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
<6>[ 15.710000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 3000 mBm), (N/A)
<6>[ 15.720000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 1700 mBm), (N/A)
<6>[ 15.730000] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz), (N/A, 2300 mBm), (N/A)
<6>[ 15.740000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 3000 mBm), (N/A)
<6>[ 15.740000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 4000 mBm), (N/A)
<6>[ 17.310000] br0: port 1(eth0) entered forwarding state
<6>[ 18.770000] device ath0 entered promiscuous mode
<6>[ 18.780000] br0: port 2(ath0) entered forwarding state
<6>[ 18.780000] br0: port 2(ath0) entered forwarding state
<6>[ 18.850000] device br0 left promiscuous mode
<6>[ 20.210000] device eth1 entered promiscuous mode
<4>[ 20.250000] ag7240_ring_free Freeing at 0x81fd5c00
<4>[ 20.250000] ag7240_ring_free Freeing at 0x81fc4800
<4>[ 20.300000] ag7240_ring_alloc Allocated 1024 at 0x816a4400
<4>[ 20.310000] ag7240_ring_alloc Allocated 2048 at 0x81fc4800
<6>[ 20.310000] reg init for 1
<4>[ 20.310000] Setting PHY...
<6>[ 20.780000] br0: port 2(ath0) entered forwarding state
<6>[ 21.350000] device eth1 left promiscuous mode
<6>[ 27.960000] nf_conntrack: automatic helper assignment is deprecated and it will be removed soon. Use the iptables CT target to attach helpers instead.
vasek00
DD-WRT Guru


Joined: 06 Nov 2010
Posts: 3312

PostPosted: Tue Sep 30, 2014 10:05    Post subject: Reply with quote
Данный роутер ревизии A на базе CPU-AR7241/AR7242 radio AR9287 и 8 port switch на RTL8309G. Можно было бы еще верх от dmesg где сам проца, и вывод ifconfig (нужно только имена сет.интерфейсов).
vudstik
DD-WRT Novice


Joined: 25 Sep 2014
Posts: 5

PostPosted: Thu Oct 02, 2014 9:37    Post subject: Reply with quote
Это был полный вывод команды dmesg. Ifconfig отдал следующие имена интерфейсов: ath0, br0, br0:0, eth0, eth1
vudstik
DD-WRT Novice


Joined: 25 Sep 2014
Posts: 5

PostPosted: Thu Oct 02, 2014 9:42    Post subject: Reply with quote
В Sysinfo -> CPU Model показывает Atheros AR7242 rev 1.1 (0x1101)
vudstik
DD-WRT Novice


Joined: 25 Sep 2014
Posts: 5

PostPosted: Mon Nov 03, 2014 16:06    Post subject: Reply with quote
Неужели никто не сталкивался с такой проблемой?
Display posts from previous:    Page 1 of 1
Post new topic   Reply to topic    DD-WRT Forum Index -> Оборудование на основе Atheros WiSOC All times are GMT

Navigation

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You cannot download files in this forum