Linksys WRT350N
From DD-WRT Wiki
Revision as of 00:13, 24 November 2016 (edit) Virtualx (Talk | contribs) m (fixed ftp link to include ftp prefex) ← Previous diff |
Current revision (00:49, 8 January 2018) (edit) (undo) Jeremywh7 (Talk | contribs) |
||
Line 1: | Line 1: | ||
- | + | Before you do anything else, check your version of the WRT350N. '''Only''' [https://wikidevi.com/wiki/Linksys_WRT350N_v1 V1] is supported, '''do not flash a V2'''. | |
- | === | + | ===Hardware=== |
+ | *FCC ID: Q87-WRT350N | ||
+ | *Power: 12 VDC, 1.25 A | ||
+ | *CPU: Broadcom BCM4705 (300 MHz) | ||
+ | *Flash/RAM: 8/32 MiB | ||
+ | *Wireless chip1: Broadcom BCM4321 | ||
+ | *Wireless chip2: Broadcom BCM2055 | ||
+ | *Wireless protocols: bgn | ||
+ | *Wireless MIMO config: 2x2:2 | ||
+ | *Antenna connector: none (fixed, non-removable) | ||
+ | *USB2.0 ports: 1 | ||
+ | ===INSTRUCTIONS=== | ||
Flashing a virgin WRT350N with the default Linksys firmware will require a special "trailed" mini-build to be flashed first. You should use a build linked in number 3, below, for the initial flash. The name of this file specifically is "dd-wrt.v24_mini_wrt350n.bin". You may proceed to flash it with a generic build next, such as Mega.bin. Remember to do the 30/30/30 Hard Reset after every successful flash. It is absolutely essential. | Flashing a virgin WRT350N with the default Linksys firmware will require a special "trailed" mini-build to be flashed first. You should use a build linked in number 3, below, for the initial flash. The name of this file specifically is "dd-wrt.v24_mini_wrt350n.bin". You may proceed to flash it with a generic build next, such as Mega.bin. Remember to do the 30/30/30 Hard Reset after every successful flash. It is absolutely essential. | ||
The proper process for flashing is: | The proper process for flashing is: | ||
- | + | # Read the [http://www.dd-wrt.com/phpBB2/viewtopic.php?t=51486 Peacock announcement], especially Note 1, 3, and 4. | |
- | # Read | + | # Download the trailed build, with the model in file name: [ftp://ftp.dd-wrt.com/betas/08-12-10-r14929/broadcom/dd-wrt.v24_mini_wrt350n.bin (14929) dd-wrt.v24_mini_wrt350n.bin] |
- | + | # [[Hard_reset_or_30/30/30|Hard reset]] the router. You will not get a password renewal page as you still have stock Linksys firmware. | |
- | # Download | + | # Plug a cable into the LAN port of the router and your computer, and disable any wireless to the computer. Disable antivirus protection. (Setting your computer to a static IP should not be required) |
- | # | + | |
- | # Plug a cable into the | + | |
# Set your browser to 192.168.1.1. This will open up the Linksys webgui | # Set your browser to 192.168.1.1. This will open up the Linksys webgui | ||
# Enter the username "admin" and password "admin" | # Enter the username "admin" and password "admin" | ||
Line 17: | Line 26: | ||
# BROWSE to the dd-wrt.v24_mini_wrt350n.bin, the file you downloaded. | # BROWSE to the dd-wrt.v24_mini_wrt350n.bin, the file you downloaded. | ||
# Click on the "upgrade" button and WAIT for the "upgrade successful" message. Wait at LEAST 5 minutes | # Click on the "upgrade" button and WAIT for the "upgrade successful" message. Wait at LEAST 5 minutes | ||
- | # Power cycle your router | + | # Power cycle your router (very important): WAIT until you can login at 192.168.1.1 |
- | # Do another | + | # Do another hard reset (very important): WAIT until you can login at 192.168.1.1 |
# Click on any tab. Reset your username/password by TYPING in a new username/password | # Click on any tab. Reset your username/password by TYPING in a new username/password | ||
# Configure your router | # Configure your router | ||
- | You can now upgrade to any generic | + | You can now upgrade to any generic DD-WRT build except micro. Power cycle followed by another hard reset after flashing, and NEVER restore a backup configuration file from a different build, type, or router. Manually reconfigure after setting a password. |
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
[[Category: Linksys]] | [[Category: Linksys]] |
Current revision
Before you do anything else, check your version of the WRT350N. Only V1 is supported, do not flash a V2.
[edit] Hardware
- FCC ID: Q87-WRT350N
- Power: 12 VDC, 1.25 A
- CPU: Broadcom BCM4705 (300 MHz)
- Flash/RAM: 8/32 MiB
- Wireless chip1: Broadcom BCM4321
- Wireless chip2: Broadcom BCM2055
- Wireless protocols: bgn
- Wireless MIMO config: 2x2:2
- Antenna connector: none (fixed, non-removable)
- USB2.0 ports: 1
[edit] INSTRUCTIONS
Flashing a virgin WRT350N with the default Linksys firmware will require a special "trailed" mini-build to be flashed first. You should use a build linked in number 3, below, for the initial flash. The name of this file specifically is "dd-wrt.v24_mini_wrt350n.bin". You may proceed to flash it with a generic build next, such as Mega.bin. Remember to do the 30/30/30 Hard Reset after every successful flash. It is absolutely essential.
The proper process for flashing is:
- Read the Peacock announcement, especially Note 1, 3, and 4.
- Download the trailed build, with the model in file name: (14929) dd-wrt.v24_mini_wrt350n.bin
- Hard reset the router. You will not get a password renewal page as you still have stock Linksys firmware.
- Plug a cable into the LAN port of the router and your computer, and disable any wireless to the computer. Disable antivirus protection. (Setting your computer to a static IP should not be required)
- Set your browser to 192.168.1.1. This will open up the Linksys webgui
- Enter the username "admin" and password "admin"
- Go to the "administration" tab. Click on "firmware upgrade".
- BROWSE to the dd-wrt.v24_mini_wrt350n.bin, the file you downloaded.
- Click on the "upgrade" button and WAIT for the "upgrade successful" message. Wait at LEAST 5 minutes
- Power cycle your router (very important): WAIT until you can login at 192.168.1.1
- Do another hard reset (very important): WAIT until you can login at 192.168.1.1
- Click on any tab. Reset your username/password by TYPING in a new username/password
- Configure your router
You can now upgrade to any generic DD-WRT build except micro. Power cycle followed by another hard reset after flashing, and NEVER restore a backup configuration file from a different build, type, or router. Manually reconfigure after setting a password.