Linksys WRT54G v7.2

From DD-WRT Wiki

(Difference between revisions)
Jump to: navigation, search
Revision as of 03:38, 18 November 2009 (edit)
DHC DarkShadow (Talk | contribs)

← Previous diff		 Current revision (10:45, 30 April 2010) (edit) (undo)
Glenn (Talk | contribs)
(catchg Category:Linksys guides)
 
(5 intermediate revisions not shown.)
Line 1: Line 1:
This install needs to be refined This install needs to be refined
 +__TOC__
Files are here Files are here
[ftp://dd-wrt.com/others/eko/WRT54G-V72%20Flashing/ WRT54G v7.2] [ftp://dd-wrt.com/others/eko/WRT54G-V72%20Flashing/ WRT54G v7.2]
-Killer & Reversion Notes for the Gv7.2+== How to Flash ==
- +<font color=red><big>'''NOTE:'''</big></font> '''During configuration or flashing a device, the only that should be hooked to the device is the computer and power.'''<br>
- +
------- VxWorksPrep-Gv72-v1 & VxWorksKiller-Gv72-v3.bin ---------+
1. Reset the router to defaults on the Linksys Admin page, and let it reboot 1. Reset the router to defaults on the Linksys Admin page, and let it reboot
or manually reboot it after its finished. or manually reboot it after its finished.
-2. go to the firmware upgrade page and browse to the VxWorksPrep-Gv72-v1.bin file, +2. go to the firmware upgrade page and browse to the [ftp://dd-wrt.com/others/eko/WRT54G-V72%20Flashing/VxWorksPrep-Gv72-v1.bin VxWorksPrep-Gv72-v1.bin] file,
and click on the upgrade page. Wait for 30 seconds for it to reboot on its own, and click on the upgrade page. Wait for 30 seconds for it to reboot on its own,
if it does not then powercycle the router manually. if it does not then powercycle the router manually.
-3. again go to the firmware upgrade page and browse to the VxWorksKiller-Gv72-v3.bin file, +3. again go to the firmware upgrade page and browse to the [ftp://dd-wrt.com/others/eko/WRT54G-V72%20Flashing/VxWorksKiller-Gv72-v3.bin VxWorksKiller-Gv72-v3.bin] file,
and click on the upgrade page. Wait for 60 seconds for it to reboot on its own, and click on the upgrade page. Wait for 60 seconds for it to reboot on its own,
if it does not then powercycle the router manually. if it does not then powercycle the router manually.
-4. Tftp the DD-WRT firmware to the router "dd-wrt.v24_micro_generic.bin" from v24 RC7 +4. Tftp the DD-WRT firmware to the router [ftp://dd-wrt.com/others/eko/WRT54G-V72%20Flashing/dd-wrt.v24_micro_generic.bin dd-wrt.v24_micro_generic.bin], after sucessful
-(or the one in this folder); this firmware is for the Gv7.2, Gv8 and GSv7, after sucessful +
tftp, wait 3 min for the router to finish writing new nvram deafults, etc... It should tftp, wait 3 min for the router to finish writing new nvram deafults, etc... It should
reboot on it's own at least two times, so give it the three min's and then goto reboot on it's own at least two times, so give it the three min's and then goto
-http://192.168.1.1 +http://192.168.1.1
------- VxWorksRevert-Gv72-v3.bin ----------+== How to upgrade firmware ==
 +If dd-wrt is already loaded on the router, simply upgrade through the GUI.
 +== How to revert ==
1. Reset to defaults 1. Reset to defaults
-2. goto the Admin screen firmware upgrade, and browse to VxWorksRevert-Gv72-v3.bin, +2. goto the Admin screen firmware upgrade, and browse to [ftp://dd-wrt.com/others/eko/WRT54G-V72%20Flashing/VxWorksRevert-Gv72-v3.bin VxWorksRevert-Gv72-v3.bin],
and click upgrade. During this time the Web browser may say upgrade succesfull and and click upgrade. During this time the Web browser may say upgrade succesfull and
to reboot -----"Do NOT REBOOT"----- Wait for 2 min's and then reboot. to reboot -----"Do NOT REBOOT"----- Wait for 2 min's and then reboot.
Line 43: Line 43:
5. go to http://192.168.1.1 - you should have the regular Linksys Firmware. 5. go to http://192.168.1.1 - you should have the regular Linksys Firmware.
- +== Notes ==
-Notes.....+
- +
It may be nessasary to completly close and repoen the browser, it sometimes will return It may be nessasary to completly close and repoen the browser, it sometimes will return
to a mgmt screen, if you only refresh the browser after upgrading, just close the browser to a mgmt screen, if you only refresh the browser after upgrading, just close the browser
Line 51: Line 49:
 +==Related==
 +[[Linksys_WRT54G_v7.2_(FR)]]
- +[[Category:Linksys guides]]
-FLASHER le firmware d'un Linksys WRT54G v7.2+
----------------------------------------------+
- +
-Avant toute chose, fermez toutes les instances de Firefox et utilisez InternetExplorer (des +
-problemes ont été rencontrés avec Firefox).+
- +
-1. Allez a l'adresse du routeur (d'origine, c'est 192.168.1.1, mais elle a pu etre changée), +
-ouvrez l'onglet Admin puis "Restore default" Cliquer suz YES puis OK. Les parametres d'origine +
-du routeur sont donc ainsi remis a zéro.+
- +
-2. Allez a la nouvelle adresse du routeur (192.168.1.1), puis a la page de mise a niveau et +
-sélectionnez via l'explorateur le fichier VxWorksPrep-Gv72-v1.bin. Attendez 30 secondes, jusqu'a +
-ce qu'il redémarre de lui-meme. S'il ne redémarre par, redémarrez-le manuellement (en enlevant et +
-remettant le câble d'alimentation).+
- +
-3. Apres le redémarrage, rouvrez 192.168.1.1 et allez a nouveau sur la page de mise a niveau du +
-firmware et sélectionnez via l'explorateur le fichier VxWorksKiller-Gv72-v3.bin. Attendez 60 secondes +
-qu'il redémarre de lui-meme et s'il ne le fait pas, redémarrez-le manuellement.+
- +
-4. Préparation de l'installation TFTP : celle-ci se fera via une fenetre de commande, laquelle +
-exécute généralement les commandes dans C\Documents and Settings\Propriétaire). Copiez le +
-firmware "dd-wrt.v24_micro_generic.bin" dans C\Documents and Settings\Propriétaire.+
-Ouvrez ensuite une fenetre de commande (Windows+R > CMD) et tapez +
-"tftp -i 192.168.1.1 PUT dd-wrt.v24_micro_generic.bin dd-wrt.v24_micro_generic.bin".+
-Apres avoir réussi l'installation tftp, laissez au moins 3 minutes au routeur pour définir +
-les nouveaux parametres. Il devrait redémarrer de lui-meme au moins deux fois. Allez a 192.168.1.1 +
-et admirez le travail !+
- +
-___________________________________________________________________________+
- +
- +
-RESTAURER le firmware d'origine+
--------------------------------+
-1. Restaurez les parametres par défaut (via l'interface dd-wrt > Admin > Restore default).+
- +
-2. Ouvrez l'onglet Admin puis celui de la mise a niveau du firmware et sélectionez via +
-l'explorateur VxWorksRevert-Gv72-v3.bin. Durant la procédure de mise a niveau, votre navigateur +
-pourrait dire que l'installation est faite et proposer de redémarrer. N'en faites rien et attendez +
-au moins deux minutes avant de le redémarrer vous-meme.+
- +
-3. Rendez-vous a 192.168.1.1 ou vous devriez voir un écran de contrôle. C'est la que vous +
-sélectionnez via l'explorateur le firmware d'origine de votre Linksys et l'installez.+
- +
-4. Attendez au moins une minute, meme si l'interface dit que la mise a niveau a été effectuée !+
- +
-5. Ouvrez 192.168.1.1 ou vous devriez normalement voir l'interface Web d'origine du routeur.+
- +
-Note : si en cours d'installation d'un des dux fichiers l'écran n'affiche pas ce a quoi vous vous +
-attendiez, vous pouvez au lieu de rafraîchir la page completement fermer le navigateur web et le rouvrir.+
- +
-____________________________________________________________________________+
- +
-Merci a Eko pour ses indications et pour la réalisation des fichiers nécessaires au flashage du routeur :-).+
-Trad : LaCombine.+

Current revision

This install needs to be refined

Contents

Files are here

WRT54G v7.2

[edit] How to Flash

NOTE: During configuration or flashing a device, the only that should be hooked to the device is the computer and power.

1. Reset the router to defaults on the Linksys Admin page, and let it reboot or manually reboot it after its finished.

2. go to the firmware upgrade page and browse to the VxWorksPrep-Gv72-v1.bin file, and click on the upgrade page. Wait for 30 seconds for it to reboot on its own, if it does not then powercycle the router manually.

3. again go to the firmware upgrade page and browse to the VxWorksKiller-Gv72-v3.bin file, and click on the upgrade page. Wait for 60 seconds for it to reboot on its own, if it does not then powercycle the router manually.

4. Tftp the DD-WRT firmware to the router dd-wrt.v24_micro_generic.bin, after sucessful tftp, wait 3 min for the router to finish writing new nvram deafults, etc... It should reboot on it's own at least two times, so give it the three min's and then goto http://192.168.1.1

[edit] How to upgrade firmware

If dd-wrt is already loaded on the router, simply upgrade through the GUI.

[edit] How to revert

1. Reset to defaults

2. goto the Admin screen firmware upgrade, and browse to VxWorksRevert-Gv72-v3.bin, and click upgrade. During this time the Web browser may say upgrade succesfull and to reboot -----"Do NOT REBOOT"----- Wait for 2 min's and then reboot.

3. Go to http://192.168.1.1 and you should see a mgmt mode screen, this is where you browse to the original Linksys Firmware, and and upgrade.

4. Wait for 1 min, even if it say's upgrade successful and to reboot, believe me, in my tests, it has not finished yet.

5. go to http://192.168.1.1 - you should have the regular Linksys Firmware.

[edit] Notes

It may be nessasary to completly close and repoen the browser, it sometimes will return to a mgmt screen, if you only refresh the browser after upgrading, just close the browser and try again.


[edit] Related

Linksys_WRT54G_v7.2_(FR)

Retrieved from "http://wiki.dd-wrt.com/wiki/index.php/Linksys_WRT54G_v7.2"