hardware:8devices:carambola_2

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
hardware:8devices:carambola_2 [2015/05/16 15:07]
admin [uboot - Bootloader]
hardware:8devices:carambola_2 [2018/05/24 09:05] (current)
Line 12: Line 12:
 |     ^ CPU            ^ Frequency ​  ^ RAM    ^ Flash   ^ Ethernet ​ ^ Wireless ​    ^ USB    ^ Serial ​  ^ JTAG ^ |     ^ CPU            ^ Frequency ​  ^ RAM    ^ Flash   ^ Ethernet ​ ^ Wireless ​    ^ USB    ^ Serial ​  ^ JTAG ^
 ^   | Atheros AR9331 | 400 MHz     | 16 MB  | 64 MB  | 2 x 100Base-T | b/g/n 150 Mbps | 1x 2.0 | via miniUSB | ?  | ^   | Atheros AR9331 | 400 MHz     | 16 MB  | 64 MB  | 2 x 100Base-T | b/g/n 150 Mbps | 1x 2.0 | via miniUSB | ?  |
- 
-===== Serial connection ===== 
- 
-A serial console is available on the external miniUSB connector: 
- 
-  115200 8N1, no hardware flow-control 
  
 ===== Installation instructions ===== ===== Installation instructions =====
Line 25: Line 19:
 The bootprocess can be interrupted by pressing '​ESC'​ The bootprocess can be interrupted by pressing '​ESC'​
  
-  ​tftp 80060000 ddwrt-ar71xx-generic-carambola2-initramfs-kernel.bin+uboot commands: 
 +  ​tftp 80060000 ddwrt-ar71xx-generic-carambola2-squashfs-sysupgrade.bin
   erase 9f050000 +${filesize}   erase 9f050000 +${filesize}
   cp.b 80060000 9f050000 ${filesize}   cp.b 80060000 9f050000 ${filesize}
   reset   reset
  
 +===== Serial connection =====
 +
 +A serial console is available on the external miniUSB connector:
 +
 +  115200 8N1, no hardware flow-control
 +
 +===== Bootlog =====
 +<​code>​
 +## Booting image at 9f050000 ...
 +   Image Name:   MIPS OpenWrt Linux-3.18.11
 +   ​Created: ​     2015-05-16 ​ 14:45:23 UTC
 +   Image Type:   MIPS Linux Kernel Image (lzma compressed)
 +   Data Size:    11661548 Bytes = 11.1 MB
 +   Load Address: 80060000
 +   Entry Point: ​ 80060000
 +   ​Verifying Checksum at 0x9f050040 ...OK
 +   ​Uncompressing Kernel Image ... OK
 +
 +Starting kernel ...
 +
 +[    0.000000] Linux version 3.18.11 (markus@dd-workstation) (gcc version 4.8.3 (OpenWrt/​Linaro GCC 4.8-2014.04 r45560) ) #2 Sat May 16 16:45:16 CEST 2015
 +[    0.000000] bootconsole [early0] enabled
 +[    0.000000] CPU0 revision is: 00019374 (MIPS 24Kc)
 +[    0.000000] SoC: Atheros AR9330 rev 1
 +[    0.000000] Determined physical RAM map:
 +[    0.000000] ​ memory: 04000000 @ 00000000 (usable)
 +[    0.000000] Initrd not found or empty - disabling initrd
 +[    0.000000] Zone ranges:
 +[    0.000000] ​  ​Normal ​  [mem 0x00000000-0x03ffffff]
 +[    0.000000] Movable zone start for each node
 +[    0.000000] Early memory node ranges
 +[    0.000000] ​  ​node ​  0: [mem 0x00000000-0x03ffffff]
 +[    0.000000] Initmem setup node 0 [mem 0x00000000-0x03ffffff]
 +[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
 +[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
 +[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
 +[    0.000000] Kernel command line:  board=CARAMBOLA2 mtdparts=spi0.0:​256k(u-boot)ro,​64k(u-boot-env)ro,​16000k(firmware),​64k(art)ro console=ttyATH0,​115200 rootfstype=squashfs,​jffs2 noinitrd
 +[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
 +[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
 +[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
 +[    0.000000] Writing ErrCtl register=00000000
 +[    0.000000] Readback ErrCtl register=00000000
 +[    0.000000] Memory: 50832K/​65536K available (2487K kernel code, 123K rwdata, 528K rodata, 10356K init, 188K bss, 14704K reserved)
 +[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0,​ CPUs=1, Nodes=1
 +[    0.000000] NR_IRQS:51
 +[    0.000000] Clocks: CPU:​400.000MHz,​ DDR:​400.000MHz,​ AHB:​200.000MHz,​ Ref:​40.000MHz
 +[    0.000000] Calibrating delay loop... 265.42 BogoMIPS (lpj=1327104)
 +[    0.080000] pid_max: default: 32768 minimum: 301
 +[    0.080000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
 +[    0.090000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
 +[    0.100000] NET: Registered protocol family 16
 +[    0.100000] MIPS: machine is 8devices Carambola2 board
 +[    0.600000] Switched to clocksource MIPS
 +[    0.600000] NET: Registered protocol family 2
 +[    0.610000] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
 +[    0.610000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
 +[    0.610000] TCP: Hash tables configured (established 1024 bind 1024)
 +[    0.620000] TCP: reno registered
 +[    0.620000] UDP hash table entries: 256 (order: 0, 4096 bytes)
 +[    0.630000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
 +[    0.640000] NET: Registered protocol family 1
 +[   ​17.760000] futex hash table entries: 256 (order: -1, 3072 bytes)
 +[   ​17.770000] squashfs: version 4.0 (2009/​01/​31) Phillip Lougher
 +[   ​17.770000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
 +[   ​17.790000] msgmni has been set to 99
 +[   ​17.800000] io scheduler noop registered
 +[   ​17.800000] io scheduler deadline registered (default)
 +[   ​17.800000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
 +[   ​17.810000] ar933x-uart:​ ttyATH0 at MMIO 0x18020000 (irq = 11, base_baud = 2500000) is a AR933X UART
 +[   ​17.820000] console [ttyATH0] enabled
 +[   ​17.820000] console [ttyATH0] enabled
 +[   ​17.830000] bootconsole [early0] disabled
 +[   ​17.830000] bootconsole [early0] disabled
 +[   ​17.840000] m25p80 spi0.0: found w25q128, expected m25p80
 +[   ​17.840000] m25p80 spi0.0: w25q128 (16384 Kbytes)
 +[   ​17.850000] 4 cmdlinepart partitions found on MTD device spi0.0
 +[   ​17.850000] Creating 4 MTD partitions on "​spi0.0":​
 +[   ​17.860000] 0x000000000000-0x000000040000 : "​u-boot"​
 +[   ​17.860000] 0x000000040000-0x000000050000 : "​u-boot-env"​
 +[   ​17.870000] 0x000000050000-0x000000ff0000 : "​firmware"​
 +[   ​17.910000] 2 uimage-fw partitions found on MTD device firmware
 +[   ​17.920000] 0x000000050000-0x000000fa0000 : "​kernel"​
 +[   ​17.920000] 0x000000fa0000-0x000000ff0000 : "​rootfs"​
 +[   ​17.930000] mtd: device 4 (rootfs) set to be root filesystem
 +[   ​17.930000] mtdsplit: no squashfs found in "​rootfs"​
 +[   ​17.940000] mtdsplit: no squashfs found in "​spi0.0"​
 +[   ​17.940000] 0x000000ff0000-0x000001000000 : "​art"​
 +[   ​17.960000] libphy: ag71xx_mdio:​ probed
 +[   ​18.560000] ag71xx-mdio.1:​ Found an AR7240/​AR9330 built-in switch
 +[   ​18.590000] eth0: Atheros AG71xx at 0xba000000, irq 5, mode:GMII
 +[   ​19.180000] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.1:​04 [uid=004dd041,​ driver=Generic PHY]
 +[   ​19.190000] eth1: Atheros AG71xx at 0xb9000000, irq 4, mode:MII
 +[   ​19.190000] TCP: cubic registered
 +[   ​19.190000] NET: Registered protocol family 17
 +[   ​19.200000] bridge: automatic filtering via arp/​ip/​ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
 +[   ​19.210000] 8021q: 802.1Q VLAN Support v1.8
 +[   ​19.300000] Freeing unused kernel memory: 10356K (80373000 - 80d90000)
 +[   ​19.320000] init: failed to symlink /tmp -> /var
 +[   ​19.320000] init: Console is alive
 +[   ​19.330000] init: - watchdog -
 +[   ​19.370000] usbcore: registered new interface driver usbfs
 +[   ​19.370000] usbcore: registered new interface driver hub
 +[   ​19.380000] usbcore: registered new device driver usb
 +[   ​19.430000] SCSI subsystem initialized
 +[   ​19.440000] ehci_hcd: USB 2.0 '​Enhanced'​ Host Controller (EHCI) Driver
 +[   ​19.450000] ehci-platform:​ EHCI generic platform driver
 +[   ​19.450000] ehci-platform ehci-platform:​ EHCI Host Controller
 +[   ​19.460000] ehci-platform ehci-platform:​ new USB bus registered, assigned bus number 1
 +[   ​19.470000] ehci-platform ehci-platform:​ irq 3, io mem 0x1b000000
 +[   ​19.500000] ehci-platform ehci-platform:​ USB 2.0 started, EHCI 1.00
 +[   ​19.500000] hub 1-0:1.0: USB hub found
 +[   ​19.500000] hub 1-0:1.0: 1 port detected
 +[   ​19.510000] usbcore: registered new interface driver usb-storage
 +[   ​20.330000] init: - preinit -
 +[   ​20.640000] procd: - early -
 +[   ​20.640000] procd: - watchdog -
 +[   ​21.220000] procd: - ubus -
 +[   ​22.220000] random: ubusd urandom read with 34 bits of entropy available
 +[   ​22.240000] procd: - init -
 +Please press Enter to activate this console.
 +
 +
 +
 +BusyBox v1.23.2 (2015-05-16 16:41:05 CEST) built-in shell (ash)
 +
 + ​____ ​ ____     _ _ _ _____ _____    _____ __ __ _____
 +|    \|    \ __| | | | __  |_   ​_| ​ |   | |  |  |_   _|
 +|  |  |  |  |__| | | |    -| | |    | | | |>   < ​ | |
 +|____/​|____/ ​  ​|_____|__|__| |_|    |_|___|__|__| |_|
 +
 + ​----------------------------------------------------
 +   Made by embeDD GmbH (Bleeding Edge, r45560)
 + ​----------------------------------------------------
 +root@dd-wrt-nxt:/#​
 +</​code>​
  
hardware/8devices/carambola_2.1431788874.txt.gz · Last modified: 2018/05/24 09:05 (external edit)